FORCED DRAFT COOLER (Used) Built in 1996 Design Pressure: 1480 PSI @ 200° F MDMT: -40° F Bare Surface Area: 3,862 Ft.² Tubes: 309 x 1″ 16 BWG x 48′ Long Tube Material: 316 Stainless Steel Header Material: 304 Stainless Steel Inlet & Outlet: 8″ 900# RFWN Fan Motors: 2 x 40HP (460/3/60) Shipping Dimensions: […]
BLAST RESISTANT WASH CAR Built in 2015 12′ W x 40′ L x 11’ H (Skid Mounted) Peak Side on Pressure: 8 PSI @ 200 MSEC Men’s Washroom: 4 Cubicles, 5 Urinals & 4 Sinks Women’s Washroom: 2 Cubicles & 1 Sink Bard Heating & Ventilation Unit Mounted Outside Pumps: 2 x 2 HP (Includes […]
90″ ID VERTICAL SEPARATOR VESSEL Built in 2009 Sour Service 90″ ID x 10′-6″ S/S 26′-5″ OAL 1870 PSI @ 250° F 3-Phase Heads: SA-516-70N Shell: SA-516-70N RT-1 Heat Treated: Full CA: 0.187″ “U” Stamp: Yes MDMT: -20° F @ 1870 PSI Inlet: 12″ 900# RFWN Outlet: 16″ 900# RFWN Outlet: 4″ 900# RFWN Manway: 24″ […]
CENTRIFUGAL PUMPS c/w 10 HP Motors – 2 Manufacturer & Model: Clyde Union SPX Pump Size: 1.5 x 2 x 8 VLK-8L MAWP: 700 PSI Head: 17′ RPM: 3550 Capacity: 108 USGPM @ 50 PSI Dif. Electric Motor: 10 HP XP, 230/460V/3/60 Never put into service & stored in Alberta
GLYCOL BUILDING HEATERS (RUFFNECK) – 2 Model: AH-20A-A3A1-A1-2A FAN: 20″ Electric Motor: 1 PH 60 Hz .5 Hp Explosion Proof Never used & stored in Alberta
DEHYDRATION PLANT – MOLE SIEVE Built in 1996 Mole Sieve Towers (3) Size: 78″ ID x 24′-0″ S/S Design Pressure: 1440 PSI @ 650° F Inlet: 8″ 900# RFWN Outlet: 6″ 900# RFWN Weight: 130.200 Lbs. Each Status: Disconnected but still standing Forced Draft Cooler (Inlet) Bare Surface Area: 2,935 Ft.² Design Pressure: 1440 PSI […]
REBOILER Built in 2015 and never used Type: BKU Rating: 2.8MMBTU/H Size: 20″ OD x 30″ OD x 25′-0″ S/S Design Pressure Shell: 260 PSI @ 450° F Design Pressure Tubes: 260 PSI @ 500° F Inlet: (2) 4″ 300# RFWN Outlet: (2) 6″ 300# RFWN Corrosion Allowance: 0.0625″ Weight: 9000 Lbs. Status: Currently connected […]
PRESSURE SWING ADSORBERS (4) Built in 2011 and never used 138″ ID x 23′-5″ S/S 43′-9″ OAL 500 PSI @ 250° F Corrosion Allowance: .063″ MDMT: -45° F @ 500 PSI RT-1 CRN #: V2062.2 “U” Stamp: Yes National Board #: Yes Head Material: SA-516-70N Shell Material: SA-516-70N Inlet: 20″ 300# RFWN Outlet: 24″ 300# […]
STUDS, NUTS & TWO WASHERS – 500 1″ x 2½” SA 320 Never used and stored in Alberta
STUDS, NUTS & TWO WASHERS – 500 1″ x 2½” SA 320 Never used and stored in Alberta
EXCHANGER – BKU Manufacturer: Exchanger Industries in 2009 Tema Type: BKU 26MMBtu/h Heat Surface Area: 3771.6 Ft.² Size: 40/57-273 Shell: 50 PSI @ 300° F Tube: 125 PSI @ 300° F Shell Material: SA-240-316L Tube Material: SA-789-UNS-31803 CA Channel: 0.125″ RT-1 “U” Stamp Insulated: Yes Weight: 30,690 LBS Never used & stored in Alberta
HEADS & SHELLS Size: 168″ ID x 120″ Long x 0.75″ WT Quantity Heads: 2 Quantity Shells: 7 Material: SA-516-70 (Conforms to NACE) One long seam weld completed on shells One long seam tack welded and braced on shells Head Weight: 8,300 Lbs Shell Weight: 13,547 Lbs. MTR’s available Never used & stored in Alberta […]
HEADS & SHELLS Size: 168″ ID x 120″ Long x 1″ WT (0.875″ Min.) Quantity Heads: 2 Quantity Shells: 10 Material: SA-516-70 (Conforms to NACE) One long seam weld completed on shells One long seam tack welded and braced on shells Head Weight: 9,500 Lbs Shell Weight: 15,876 Lbs. MTR’s available Never used & stored […]
VERTICAL CARBON FILTER Built in 2009 as a Rich Amine Filter Sour Service PS Filter Model: 72-240-3F-258 6′-0″ OD x 20′-0″ S/S 256 PSI @ -50 / 212° F Inlet & Outlet: 3″ 150# RF Manways (2): 24″ 150# RF CA: 0.25″ MDMT: -50° F Element Type: Dumped Carbon Original Design Capacity: 6,340 Gallons per […]
PRESSURE SWING ADSORBERS (4) Built in 2011 and never used 138″ ID x 23′-5″ S/S 43′-9″ OAL 500 PSI @ 250° F Corrosion Allowance: .063″ MDMT: -45° F @ 500 PSI RT-1 CRN #: V2062.2 “U” Stamp: Yes National Board #: Yes Head Material: SA-516-70N Shell Material: SA-516-70N Inlet: 20″ 300# RFWN Outlet: 24″ 300# […]
PRESSURE SWING ADSORBERS (4) Built in 2011 and never used 138″ ID x 23′-5″ S/S 43′-9″ OAL 500 PSI @ 250° F Corrosion Allowance: .063″ MDMT: -45° F @ 500 PSI RT-1 CRN #: V2062.2 “U” Stamp: Yes National Board #: Yes Head Material: SA-516-70N Shell Material: SA-516-70N Inlet: 20″ 300# RFWN Outlet: 24″ 300# […]
WATER FILTRATION SKIDS (2) Filter Housing: Peco Model 57-66-229-28-701-6F Design Pressure: 701 PSI @ -20 / 160° F 6″ 300# Inlet & Outlet Weight: 3,815 Lbs. Never used & stored in Alberta
WATER FILTERS – 2 Filter Housing: Peco Model 57-66-229-28-701-6F Design Pressure: 701 PSI @ -20 / 160° F 6″ 300# Inlet & Outlet Weight: 3,815 Lbs. Never used & stored in Alberta
4″ 900# RF HIGH TEMPERATURE CHOKE VALVES (45 Units) Master Flo Model P4E High Temperature 4″ 900# RF Inlet & Outlet Rated Pressure: 2160 PSIG Temp. Range: -20 / 650 ° F Material Class: EE-0.5 PSL-1 Trim: Tungsten Carbide Seals: Graphoil Bean Size: 214/64 PDA 200 Pneumatic Actuator (open yoke) DVC 6200 HC Positioner Never used […]
CHECK VALVES (2) Cameron Wheatley Model 510/511 3″ 900# RTJ Sour Service Low Temperature Body: Carbon Steel (LCC) Clapper: Stainless Steel Internal Coating: 410 M Impreglon Never Used & Stored in Alberta
BALL VALVES (4) Cameron Grove Model B4C Size: 3″ 900 # RTJ Full Port ANSI Pressure Rating: 900# Trim: Low Temperature / Sour (NACE) Ends: Flanged RTJ Body: A350 LF2 Ball: Carbon Steel ENC Stem: Carbon Steel ENC Seat: Carbon Steel PK Seals: HNBR Internal Coating: 410 M Impreglon Never used & stored in Alberta […]
REBOILER – “BKU” Manufacturer: Exchanger Industries in 2009 Tema Type: BKU 26MMBtu/h Heat Surface Area: 3681.6 Ft.² Size: 40/57-273 Shell: 50 PSI @ 300° F Tube: 333 PSI @ 400° F Head Material: SA-240-316L Stainless Steel Tube Material: SA-789-UNS31803 Duplex Stainless Steel CA Channel: 0.125″ RT-1 “U” Stamp Insulated: No Weight: 30,690 LBS Never used […]
VERTICAL CHARCOAL FILTER Built in 2009 as a Rich Amine Filter Sour Service PS Filter Model: PB-18-330-3F-256-1 18″ OD x 36″ S/S 256 PSI @ 212 ° F Inlet & Outlet: 3″ 150# RF Manway: 18″ 150# Quick Closure CA: 0.25″ MDMT: -50° F Element Type: PCB-10AB-24P Design Capacity: 5,547 Gallons/h Insulated: No Heat Traced: […]
EXCHANGER SHELL & PIPE Manufacturer: Enerflex in 2009 Pipe Surface Area: 212 Ft.² Size: 36″ OD x 20′-0″ S/S Shell: 190 PSI @ 400° F Pipe: 200 PSI @ 400° F Pipes (3″ OD): 8 Passes of 3″ Sch. XH Head Material: SA-516-70N Shell Material: SA-516-70N Pipe Material: SA-333-Gr. 6 Corrosion Allowance: 0.125″ P.W.H.T: No […]
24″ OD VERTICAL SEPARATOR VESSEL Built in 2009 24″ OD x 6′-0″ S/S 1415 PSI @ 151° F Gas Inlet: 6″ 600# RF Gas Outlet: 4″ 600# RF Liquid Outlet: 2″ 600# RF Steam Outlet: 2″ 600# RF RT-1 Never Used & stored in Alberta
EXCHANGERS – HAIRPIN (3) Built in 2017 and never put into service Shell: 405 PSI @ 410° F Tube: 630 PSI @ 410° F Shell / Unit: 1 Surface / Shell Gross: 2412 Ft.² each Surface / Shell Eff: 2404 Ft.² each Surface / Unit Gross: 4824 Ft.² each Surface / Unit Eff: 4808 Ft.² […]
EXCHANGERS – HAIRPIN (2) Built in 2017 and never put into service Heat exchanged: 10,441,153 BTU/H (Pair) Shell: 218 PSI @ 353° F Tube: 168 PSI @ 353° F Shell / Unit: 2 Surface / Shell Gross: 265 Ft.² (Pair) Surface / Shell Eff: 259 Ft.² (Pair) Surface / Unit Gross: 265 Ft.² (Pair) Surface […]
PROPANE CONDENSER / PRODUCT COOLER Built in 2009 and never used Aerial Cooler: Ace Model E-54-7 c/w 15 HP Motor Propane Condenser: 300 PSI @ 200° / -20° F (333,295 Btu/h) Product Cooler: 400 PSI @ 300° / -20° F (44,000 Btu/h) Accumulator Vessel: 20″ OD x 8′-0″ S/S, 300 PSIG Dryer: Sporlan C-1448 300 […]
WAC POLISHER EXCHANGER VESSEL Built by Ecodyne in 2013 13′-0″ OD x 7′-6″ T/T Design Pressure: 150 PSI @ 200° F Full Vacuum CA: 0.125″ RT-2 “U” Stamp Alberta Registration Inlet & Outlets: 12″ 150# RFWN Media Removal: 6″ 150# RFWN Top Manway: 24″ 150# RFWN Bottom Manway: 24″ 150# RFWN External Cladding Internals: 316L […]
AFTER FILTER VESSEL Built by Ecodyne in 2013 13′-0″ OD x 5′-0″ Design Pressure: 150 PSI @ 200° F Full Vacuum CA: 0.125″ RT-2 “U” Stamp Alberta Registration Inlet & Outlets: 10″ 150# RFWN Media Removal: 6″ 150# RFWN Top Manway: 24″ 150# RFWN Bottom Manway: 20″ 150# RFWN External Cladding Internals: 316L Stainless Steel […]
FORCED DRAFT COOLERS (2) Built by Amercool in 1995 Model: 1 F14-090-1 Section A: 1.00MMBTU/H DP: Atmospheric Surface Per Unit-Finned Tube: 10,410 Ft.² Tubes: 198 x 1″ OD x 14′ Long Tube Material: SA-214 Inlet / Outlet: 6″ 600# RF Section B: 0.127MMBTU/H DP: Atmospheric Surface Per Unit-Finned Tube: 2,485 Ft.² Tubes: 22 x 1″ […]
EXCHANGERS – BFU (PAIR) Built in 2013 and never put into service Shell: 204 PSI @ 650° F Tube: 265 PSI @ 318° F Material Shell: SA-516-70N Material Tube: SA-179 Effective Surface Area: 1161Ft.² (580.5 Ft.² Each) Tubes: 260 x 5/8″ “U” (130 Each) CA Tubesheet: 0.125″ RT-2 Shell RT-2 Tube Inlet Shell: 4″ 300# […]
VERTICAL PARTICLE FILTERS (3) Built in 2009 as Rich Amine Particle Filters Sour Service PS Filter Model: PB-36-1230-8F-256-1 36″ ID x 42″ S/S 256 PSI @ 212° F Inlet & OutLet: 6″ 150# RF Manway: 36″ 150# Quick Closure CA: 0.125″ MDMT: -50° F Replacement Element: PBC-5AB-24P Design Capacity: 31,753 Gallons/h Insulated: No CRN#: U-8218.2 […]
SHELLS (5) Size: 168″ ID x 120″ Long x 0.75″ WT Quantity Shells:5 Material: SA-516-70 (Conforms to NACE) One long seam weld completed on shells One long seam tack welded and braced on shells Shell Weight: 13,547 Lbs. MTR’s available Never used & stored in Alberta
HEADS & SHELLS Size: 168″ ID x 120″ Long x 1″ WT (0.875″ Min.) Quantity Heads: 2 Quantity Shells: 10 Material: SA-516-70 (Conforms to NACE) One long seam weld completed on shells One long seam tack welded and braced on shells Head Weight: 9,500 Lbs Shell Weight: 15,876 Lbs. MTR’s available Never used & stored […]
SPARGED VESSEL – STAINLESS STEEL Built by Cessco in 1994 Size: 60″ ID x 22′-7″ S/S Design Pressure: 465 PSI Design Temperature: 150° / -20° F Shell Material: SA-240-304L Head Material: SA-240-304L Radiography: No P.W.H.T.: No C.A.: No Insulated: No Weight Empty: 21,540 Lbs. N1-Inlet: TBA N2-Outlet: TBA Manway: Yes Status: Used & stored in […]
90″ ID VERTICAL SEPARATOR VESSEL Built in 2014 Sour Service 90″ ID x 24′-0″ S/S 222 PSI @ 410° F 3-Phase Heads: SA-516-70N Shell: SA-516-70N RT-1 Heat Treated: Full CA: 0.125″ “U” Stamp: Yes Inlet: 20″ 300# RFWN Outlet: 12″ 300# RFWN Liquid Outlet: 8″ 300# RFWN Manway: 24″ 300# RFWN Insulated: Yes Vessel Weight: TBA […]
FLARE KNOCKOUT DRUM – STAINLESS STEEL 78 BBl. Manufactured by Fasoli in 1989 66″ ID x 16′-0″ S/S 150 PSIG @ 149° F Head Material: SA240TP304L Stainless Steel Shell Material: SA240TP304L Stainless Steel RT-2 “U” Stamp: Yes Internally Coated: No N1 – Vapour Inlet: 12″ 150# RF N2 – Vapour Outlet: 10″ 150# RF N3 – Vapour […]
SENIOR METER RUN 6″ 600# Daniel Cat #: 015C Line Bore: 6.065″ Trim: A Plate Thickness: .125″ Design Pressure: 1480 PSI Ends: 6″ 600# RF Never used & stored in Alberta
108″ ID VERTICAL SEPARATOR VESSEL Built in 2016 Sour Service 108″ ID x 40′-0″ S/S 290 PSI @ 417° F 3-Phase Heads: SA-516-70N Shell: SA-516-70N RT-1 Heat Treated: Full CA: 0.125″ “U” Stamp: Yes Inlet: 16″ 300# RFWN Outlet: 16″ 300# RFWN Liquid Outlet: 8″ 300# RFWN Manway: 24″ 300# RFWN Insulated: Yes Vessel Weight: 73,000 […]
HYDROGENATOR VESSEL Built in 2008 11′-6″ ID x 14′-10″ S/S 42′-0″ OAL DP: 700 PSI @ 750° F Shell: SA-387 GR11 Cl2 Head: SA-387 GR11 Cl2 RT-1 Radiography: Full P.W.H.T.: Yes CA: 0.125″ Inlet: 14″ 600 RF Outlet: 24″ 600 RF Capacity: 1939 Ft.³ Weight Empty: 125,223 Lbs. CRN: Yes “U” Stamp: Yes National Board […]
VERTICAL CHARCOAL FILTERS (2) Built in 2009 as a Lean Amine Charcoal Filter Sour Service PS Filter Model: PB-18-330-3F-256-1 18″ OD x 36″ S/S 256 PSI @ 212 ° F Inlet & Outlet:3″ 150# RF Manway: 18″ RF Quick Closure CA: 0.125″ MDMT: -50° F Element Type: PBC-10-AB-24-P Original Design Capacity: 6,075 Gallons/h Insulated: No Heat […]
Feluwa Hose Diaphragm Piston Pump Pump Type: 3ZGL50/135-K-90-SM270 14D Motor: 100 HP (575/3/60) Designed to Pump 34 GPM @ 2240 PSI FELUWA hose-diaphragm pumps allow for reliable and low-wear handling of abrasive, aggressive and challenging media. Thanks to the linear flow path through the hose-diaphragm and the valves, the conveyed fluid will neither come in […]
EXCHANGER – NEN Manufacturer: Exchanger Industries in 1994 Tema Type NEN Tube Surface Area: 438.2 Ft.² Size 15-240 Tube Surface Area: Shell: 465 PSIG @ 150° F Tube: 465 PSIG @ 150° F Tubes: 116 x 0.75″ OD x 16 BWG Shell Material: SA-312-340L Stainless Steel Head Material: SA-312-340L Stainless Steel Tube Material: SA-249-304L Radiography: 100% (RT-1) Corrosion […]
EXCHANGERS – SHELL & PIPE (PAIR) Manufacturer: Enerflex in 2009 Pipe Surface Area: 279.20 Ft.² (Each) Size: 42″ OD x 30′-0″ S/S Shell: 190 PSI @ 400° F Pipe: 4500 PSI @ 400° F 8 Passes of 4″ Sch. XXL Head Material: SA-516-70N Shell Material: SA-516-70N Pipe Material: SA-333-Gr. 6 Corrosion Allowance: 0.125″ P.W.H.T: Yes […]
30″ ID VERTICAL VESSEL – REFLUX DRUM Built in 2009 Sour Service 30″ ID x 96″ S/S 50 PSIG @ 300° F CA: 0.25″ RT-1 “U” Stamp Inlet: 6″ 150# Outlet: 6″ 150# Liquid Outlet: 3″ 150# Steam Outlet: 2″ 150# Manway: 24″ 150# Mesh Pad: 6″ Thick Never used & stored in Alberta
1MMBTU/H FORCED DRAFT COOLERS (2) Built by Amercool in 1995 Model: 1 F14-090-1 Section A: 1.00MMBTU/H DP: 1315 PSIG @ 300° F / -40° F Surface Per Unit-Finned Tube: 10,410 Ft.² Tubes: 198 x 1″ OD x 14′ Long Tube Material: SA-214 Inlet / Outlet: 6″ 600# RF Section B: 0.127MMBTU/H DP: 65 PSIG @ […]
STUDS, NUTS & TWO WASHERS – 500 1″ x 2½” SA 320 Never used and stored in Alberta